In order to better cause or less condensate water can be caused or not produced, that is, the processing method of allowing the fresh air system to bear the majority of or all wet loads.The whole process.The vertical light -fitting pipe is only responsible for dry work.However, such system software is well used.However, this is also a way to deal with the application of the vertical lightweight disk system to the densely large -capacity shopping mall large -scale shopping mall engineering building.
In the first place, the leakage water pipe of the vertical air -fitting wind tube condensed water tray is not suitable for less than 0.01, and there is no place for water.The design scheme should be designed as a manual and electric water inlet valve that is taken over by the stand -up firing fans and cold water hot water pipes.In order to ensure that the condensation water at the joints such as the gate valve can be discharged along the storage disk, and the end is the end. When the design plan is for the buried built -in lightweight wind machine plate, it should be left out when the design scheme.The ducts are consistent, easy to check, and easy to enter and exit during maintenance.
Along with the improvement of the natural standards of indoor air, the application of vertical air -fitting wind machine tray, centrifugal fan, heat exchanger and other fresh air units have received positive attention.In order to ensure that the equipment is extraordinary, lets analyze how to do a good job in the cleaning of the dust of the vertical firing fan duct:
The vertical lightweight wind machine tray shoulder the main heavy responsibility of transmitting the cold and cold heat of cold water and hot water to the gas of the gase of the vertical lightweight fans.In order to ensure high -heat conduction efficiency, the appearance of the fan can be maintained as bright as possible.However, because the vertical lightweight wind machine plates are generally configured with the initial effect filter, and the holes are relatively large. In the beginning, it is inevitable that the smoke and dust are inevitable.surface layer.
If it is not cleaned on time, it will make the volume of the heat exchange device between the cold water and hot water and the fan of the fans in the vertical air -fitting wind turbine, so that the heat transfer efficiency of the fan coil can not be fully used.If there are a lot of dust that adheres to, and even the part of the gase of the heat transfer tube is blocked, it will also reduce the air volume of the vertical lightweight fan coil, so that the characteristics of the central air -conditioning characteristics will further further the characteristics of the central air -conditioning characteristics further further.reduce.
In addition to the installation of burn -ups, the installation of the fans of the fans can save the indoor space, and there are many other features. Below, I will introduce you to the common potential of the vertical lightweight fan pipe:
1. The reasonable layout of the vertical open -fitting wind machine disk is closely layout. The thin thickness is only thick, and it is properly installed on the window or concave wall. It is not easy to occupy indoor space
2. The method of vertical light -fitting wind machine plate into the air outlet method has three types of air (℃), and the upper wind (℃) war inclined into the air outlet (℃), which can be with the house.
3. The maintenance and conditioning of the installation of the vertical air -fitting wind machine disk is extremely convenient, and the joy is low
4. The residual pressure type of the vertical lightweight airboard tube can use LAP series products
5. The condensation of the vertical lightweight machine plate can be added in accordance with the regulations, and the gate valve is within the basin
6. The condensed water disk can be selected from stainless steel plates in accordance with regulations.
The key relying on the compulsory efficacy of the vertical air -fitting wind turbine relying on the centrifugal fan, which is heated when the gas is heated according to the appearance of the electric heating device. Therefore, the thermal convection heat switch between the heat pipe radiator and the gas can quickly warm up the house.gas.The vertical lightweight wind machine tray is the tail -end equipment of the air -conditioning unit. The principle of vertical light -fitting wind machine disk is the gas of continuously circulating the house in the generator crew.Heating), the vertical lightweight wind machine tray to ensure the stability of the temperature of the house.
Generally, it is sent to the room according to the resolution of the vertical lightweight airboard pipe to achieve the air -conditioning house discharge volume.However, because this type of heating method is only based on the conversion of heat, resulting in a better comfortable level in the room, it is only suitableEssenceBecause of the improvement of the vertical air -fitting wind machine plate, it has improved the cost of engineering and operating expenses, and the maintenance and supervision of vertical lightweight fan coils is also complicated.